Splint and cast without water or dust using the Woodcast range
Woodcast is a mouldable splinting and casting material made from aspen wood chips and a biodegradable polymer. It is hard as wood at room temperature, then soft, pliable and self-adhesive once heated, and it can be reheated and remoulded. Woodcast is ARTG listed (ARTG 442291).
Why You'll Love The Woodcast range
- No water, minimal clean-up. Woodcast is heated, not soaked, so there is no water bath or plaster mess.
- Two minutes to mould. It stays mouldable for about two minutes and can be reheated and reshaped later.
- Kind to staff. Contains no toxins, dust or irritants, and no isocyanates, latex or phthalates.
- Light and x-ray transparent. Once set, the splint is lightweight and durable, and does not blur on x-ray.
- Greener choice. Fully biodegradable and made from ethically forested wood.
Your day, with the Woodcast range
In an emergency department, hand clinic, ward or podiatry room, Woodcast can be heated and applied at the bedside. Layer or combine the different Woodcast products to adjust support and rigidity, and speed up cooling with a cold pack if needed.
The Woodcast range in a nutshell
- Ribbon: 1mm non-vented, for finger and thumb splinting and reinforcement.
- 2mm sheets and precuts: upper limb and smaller lower limb applications.
- 4mm vented sheets: thick, supportive splints, used for lower limb applications.
- Heating: use with a Woodcast heating device.
Choosing the right Woodcast product
Every Woodcast product is heated, not soaked, and you can layer or combine them to adjust support.
| Option | Size and pack | Typical use |
| 1mm ribbon D8750 | 8cm x 7.5m, 1 roll | Finger, thumb, reinforcing |
| 2mm sheet C1434S | Non-vented, 14.5 x 34cm, 20pk | Upper limb, hand therapy |
| 2mm 4-in-1 C1441 | Vented pre-cut, 14.5 x 29cm, 20pk | Upper limb |
| 2mm OneStep C1465 | Vented pre-cut, 14.5 x 65cm, 10pk | Above-elbow casts |
| 4mm sheet B1540 | Vented, 15 x 40cm, 20pk | Lower limb |
| 4mm sheet B1580 | Vented, 15 x 80cm, 10pk | Lower limb |
The 2mm non-vented sheet and the 4-in-1 pre-cut are black, the rest are natural. If you fold the B1580 sheet in the Express Heater, use a spacer.
Is it the right Woodcast product for you?
- A good fit: clinicians in emergency departments, hand clinics, wards and podiatry rooms who want splinting and casting with no water bath or plaster dust.
- Not included: a heater. Woodcast is used with a Woodcast heating device.
Woodcast is a professional casting and splinting material for clinicians. Vented Woodcast is intended for fracture management and non-vented Woodcast mainly for hand therapy. The 1mm ribbon should only be used for fractures when combined with stronger Woodcast products. We recommend speaking with your healthcare provider about any splinting needs.
Woodcast range specifications
| Material | Aspen wood chips and biodegradable polymer |
| Working time | Stays mouldable for about 2 minutes, re-mouldable |
| ARTG | 442291 |
| Free from | Toxins, dust, irritants, isocyanates, latex and phthalates |
| Cleaning | Wash in water under 40C with a brush and mild detergent such as hand soap |
Not sure which Woodcast product? Email us
Email support@mobilityshopdirect.com.au with the answers below. Our team will check them and come back to you with the right Woodcast product, or a better match if this one isn't it.
- What are you making: a finger or thumb splint, a hand or wrist splint, an above-elbow cast or a lower limb splint?
- Is it for fracture management or hand therapy?
- Which heating device do you use?
- How many packs of each product do you need?
- What setting is it for: emergency, hand clinic, ward or podiatry?